EVAL-ADM1023EB【PDF 12/16 页】BOARD EVAL FOR ADM1023

您好，
买卖IC网欢迎您。
请登录
免费注册

Sheet目录1214

8页 9页 10页 11页 [12页]13页 14页 15页 16页

ADM1023

Table 12. DEVICE ADDRESSES (Note 1)

ADD0 ADD1 Device Address

line low during the low period before the ninth

clock pulse, known as the Acknowledge bit. All

other devices on the bus remain idle while the

0

0

0

NC

NC

NC

1

1

1

0

NC

1

0

NC

1

0

NC

1

0011 000

0011 001

0011 010

0101 001

0101 010

0101 011

1001 100

1001 101

1001 110

selected device waits for data to be read from or

written to it. If the R/W bit is 0, the master writes

to the slave device. If the R/W bit is 1, the master

reads from the slave device.

2. Data is sent over the serial bus in sequences of

nine clock pulses, 8 bits of data followed by an

Acknowledge bit from the slave device.

Transitions on the data line must occur during the

low period of the clock signal and remain stable

during the high period, because a low-to-high

1. ADD0 and ADD1 are sampled at powerup only.

The serial bus protocol operates as follows:

1. The master initiates data transfer by establishing a

start condition, defined as a high-to-low transition

on the serial data line, SDATA, while the serial

clock line, SCLK, remains high. This indicates

that an address/data stream will follow. All slave

peripherals connected to the serial bus respond to

the start condition and shift in the next 8 bits.

These bits consist of a 7-bit address (MSB first)

plus an R/W bit, which determines the direction of

the data transfer, that is, whether data is written to,

or read from, the slave device.

The peripheral whose address corresponds to the

transmitted address responds by pulling the data

transition when the clock is high may be

interpreted as a stop signal. The number of data

bytes that can be transmitted over the serial bus in

a single read or write operation is limited only by

what the master and slave devices can handle.

3. When all data bytes have been read or written,

stop conditions are established. In write mode, the

master pulls the data line high during the 10th

clock pulse to assert a stop condition. In read

mode, the master device overrides the

Acknowledge bit by pulling the data line high

during the low period before the ninth clock pulse.

This is known as No Acknowledge. The master

then takes the data line low during the low period

before the 10th clock pulse, then high during the

10th clock pulse to assert a stop condition.

1

9

1

9

SCLK

SDATA

0

1

0

1

1

A1

A0

R/W

D7

D6

D5

D4

D3

D2

D1

D0

START BY

MASTER

FRAME 1

SERIAL BUS ADDRESS BYTE

ACK. BY

ADM1023

FRAME 2

ADDRESS POINTER REGISTER BYTE

ACK. BY

ADM1023

SCLK (CONTINUED)

1

9

SDATA (CONTINUED)

D7

D6

D5

D4

D3

D2

D1

D0

FRAME 3

DATA BYTE

Figure 15. Writing a Register Address to the Address Pointer Register,

then Writing Data to the Selected Register

ACK. BY

ADM1023

STOP BY

MASTER

1

9

1

9

SCLK

SDATA

0

1

0

1

1

A1

A0

R/W

D7

D6

D5

D4

D3

D2

D1

D0

START BY

MASTER

FRAME 1

SERIAL BUS ADDRESS BYTE

ACK. BY

ADM1023

FRAME 2

ADDRESS POINTER REGISTER BYTE

ACK. BY

ADM1023

STOP BY

MASTER

Figure 16. Writing to the Address Pointer Register Only

http://onsemi.com

12

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

我的联系方式

*

*

*

相关PDF资料

EVAL-ADM1031EB BOARD EVAL FOR ADM1031

EVAL-ADM1062TQEBZ BOARD EVALUATION FOR ADM1062TQ

EVAL-ADM1075CEBZ BOARD EVAL FOR ADM1075

EVAL-ADM1087EBZ BOARD EVALUATION FOR ADM1087

EVAL-ADM1166TQEBZ BOARD EVAL FOR ADM1166TQ

EVAL-ADM1168LQEBZ BOARD EVAL FOR ADM1168LQ

EVAL-ADM1170EBZ BOARD EVALUATION FOR ADM1170

EVAL-ADM1171EBZ BOARD EVALUATION FOR ADM1171

相关代理商/技术参数

EVAL-ADM1024EBZ 制造商:ON Semiconductor 功能描述:EVALUATION BOARD I.C. - Boxed Product (Development Kits)

EVAL-ADM1026EB 制造商:AD 制造商全称:Analog Devices 功能描述:Complete Thermal and System Management Controller

EVAL-ADM1028 制造商:AD 制造商全称:Analog Devices 功能描述:Evaluation Board for PC Temperature Monitor and Fan Control ASIC

EVAL-ADM1030 制造商:AD 制造商全称:Analog Devices 功能描述:Evaluation Board for ACPI Temperature Monitor and PWM Fan Controller

EVAL-ADM1031 制造商:AD 制造商全称:Analog Devices 功能描述:Evaluation Board for ACPI Temperature Monitor and PWM Fan Controller

EVAL-ADM1031EB 功能描述:BOARD EVAL FOR ADM1031 RoHS:否类别:编程器，开发系统 >> 过时/停产零件编号系列:- 标准包装:1 系列:- 传感器类型:CMOS 成像，彩色（RGB）传感范围:WVGA 接口:I²C 灵敏度:60 fps 电源电压:5.7 V ~ 6.3 V 嵌入式:否已供物品:成像器板已用 IC / 零件:KAC-00401 相关产品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP

EVAL-ADM1034EB 制造商:ON Semiconductor 功能描述:EVAL BOARD - Boxed Product (Development Kits)

EVAL-ADM1060EBZ 功能描述:BOARD EVALUATION ADM1060 RoHS:是类别:编程器，开发系统 >> 评估演示板和套件系列:- 标准包装:1 系列:PSoC® 主要目的:电源管理，热管理嵌入式:- 已用 IC / 零件:- 主要属性:- 次要属性:- 已供物品:板，CD，电源